Flush type wilress AP Router, model SYQT-300M
  • Item No.20220613455c2
    MOQ50 Piece / Pieces
  • Customized logo (Min. Order: 50 Piece)
  • Customized packaging (Min. Order: 50 Piece)
description

1.jpg2.jpg3.jpg4.jpg

Product Specification Sheet

Model SYQT-300M
Specification Flush type AP Router
Product Photo 
Advantage Standard 86 faceplate structure design, Small size, easy to assemble, perfect integration with home style.
Support 802.11b / g / n, maximum 300mbps wireless rate
Support standard 802.3af power supply protocol, stable and secure operation, easy to deploy.
Low power, microcellular, small interference, low radiation, good coverage, green environmental protection.
Chip Cpu and wireless chip Mediatek MT7628 
Flash memory(Flash) 8MB 
internal memory (DDR) 64MB 



physical interface RJ45 WAN/LAN (10/100Mbpssself-adaption) It is located at the back end of AP, placed in the wall, and can provide both poe power function and network multiplexing separation function.
RJ45 LAN by factory configuration, as AP LAN port output or original owner Straight-through network.

LED indicator Indicator item System operation indication, WIFI working indication, WAN/LAN port connection indication
antenna 2*2 MIMO antenna
power supply mode 220V Ac power supply
Max consumption 3W 
Wireless parameter Working frequency band 2.4GHz 
Frequency spread technique DSSS 
modulation mode DBPSK, DQPSK, QPSK, CCK and OFDM (BPSK/QPSK/16-QAM/ 64-QAM) 
transmission speed 11n: run up to 300Mbps 
11g: 54/48/36/24/18/12/9/6Mbps 
11b: 11/5.5/2/1Mbps 
route (channel) 1~13 
transmitting power (RF Power) EIRP<20dBm 100%: 18dBm±2dBm 80%: 15dBm±2dBm 60%: 12dBm±2dBm 40%: 10dBm±2dBm, Can be controlled by software.
receiving sensitivity 130M: -68dBm@10% PER 
108M: -68dBm@10% PER 54M: -68dBm@10% PER 11M: -85dBm@8% PER 6M: -88dBm@10% PER 
1M: -90dBm@8% PER 
Wireless security WPA/WPA2, WPA-PSK/WPA2-PSK (TKIP/AES) 
64/128/152 position: WEP SSID ON/OFF
MAC Address filtering
Wireless working mode AP Router, AP(Bridge) 
management style Web interface management
User name : admin 
Password:******
LAN IP:192.168.88.254 
DHCP allocation ON
remote administration OFF
Wireless working mode Router+AP(Bridge) 
default setting Wireless setting ON
SSID related SSID1: ********
route (channel) (Auto) 
Router setting WAN IP, automatic acquisition
Security setting SPI firewall ON
Wireless security open
Function Basic IEEE 802.11n, 802.11g, 802.11b, 802.11i, 802.1X, 802.3, 802.3u, 802.3X, 
) Support for power off protection (this module will automatically revert to the pre-upgrade software if the power is suddenly cut off during the upgrade)
Support for web fail-once an upgrade fails, it can be upgraded in PC connection web mode
Support multi-SSID 
Support DHCP Option60 
Support AP client isolation
Support for the limiting number of wireless clients
Support wireless transmission power adjustable
Support TCP/IP, PPPoE, DHCP, ICMP, NAT 
Support UPnP,dynamic DNS,Static routing,VPN penetration
Support Bandwidth Control based on SSID
IP address and MAC address binding / Mac address filtering
WAN port connection mode WAN Port support PPPoE, Dynammic IP,Static etc. IP connection mode 
Wireless function Support for wireless roaming, channel self-adaptation
Provide wireless data statistics
Safety regulations and electromagnetic radiation, etc. Comply with ROHS instruction
Supported agreements and standards Electrical and electronic engineer Association standard IEEE 802.11n, 802.11g, 802.11b, 802.11i, 802.1X, 802.3, 802.3u, 802.3X 
Other agreements and standards CSMA/CA, CSMA/CD, TCP/IP, DHCP, ICMP, NAT, PPPoE, SNTP 
working atmosphere working temperature -10℃~60℃ 
Storage temperature -40 degree~70 degree 
Working humidity 10%~90% RH Non-condensation
Storage humidity 5%~90% RH Non-condensation

product size: 86mm*86mm*40mm

I. equipment installation
1.Remove the lower cover-remove the face cover from the panel with a screwdriver.

 

2. Connecting power cord to network cable
Connect 220V power cord and network cable to the interface specified on the back of the panel to make sure the connection is firm (note: when connecting the 220V power cord, please cut off the power supply and then connect it again, to avoid electrical shock)


3. Mounting screw
Take out the screw from the packing box, put the router in the bottom box, adjust the screw hole position in the bottom box, and tighten the screw to fix the router.

4. Installation cover
After the router is fixed, to cover the router panel and clip the cover into the slot on the panel.

 

II. Mode function introduction
1. Wireless AP mode
Wireless AP mode converts wired networks to wireless networks. Connect this wireless AP router to a wired network to which computers and other portable devices can be wirelessly connected.
2.Main routing mode
This router initiates a PPPoE connection to the internet (generally refers to ADSL line, or a dial-up network connection is required, and the PPPoE username and password assigned by the network operator are set on the configuration page. The computer and other portable devices can be connected to the network wirelessly after the connection.
3.Wireless relay mode (bridging)

III.Setting up a router
1.Connect to the device network
Click the wireless network icon in the lower right corner of the desktop to display all nearby wireless networks and double-click the router's wireless network name, namely SSID. (the default SSID for this router is YQTxxxxxx.
2. Open the browser, access 192.168.7.1, and enter the administration interface. (user name, password defaults to admin). 
3.Select AP Mode, Router Mode, Relay Mode in Mode selection options
1)AP mode - set up the wireless network name SSID, to click confirm the password, will be able to access the wireless Internet.
2)Router mode – enter the PPPoE account number assigned by the network operator, password or select a static IP address.
3)Wireless Relay Mode - after connecting to the router, select a superior wireless signal to connect.

Note: the default mode for the product ex-factory is set up routing mode. When you change to AP mode, you need to manually change the IP address of your computer or other portable device to reach the administrative interface when accessing the interface.

FAQ (troubleshooting) 
1 How to restore factory setting?
Press 5 to 10 seconds into the rst hole of the panel with a small needle, and the system will revert to the factory setting.
2 Why can't my laptop search for wireless signals?
1) Make sure the computer's wireless switch is ON normally.
2) Confirm that the wireless router is powered up.
3) Confirm the presence of serious interference sources (wireless phones, microwave ovens). If not, restore the router to factory settings.
3 Forget the key of wireless encryption?
1) Connect computers and routers using wire, log in to wireless routers wired and view the parameters associated with wireless security settings
2) Restore wireless routers to factory settings.

Have more questions about this product?

Scan the QR code with your phone, or visit the URL

https://www.mcbrcd.com/

Have more questions about this product?
  • Qian Xi Yang Village, Liushi Town, Wenzhou, Zhejiang, China
  • +86 15158431127
  • [email protected]